Arsenal Steel Buildings Panel Specifications

All panels fabricated from first-run top-grade steel
All 26-gauge material is .0185 mil, 80,000 PSI
All 29-gauge material is .0157 mil, 80,000 PSI
Bare panels coated with Bare GALVALUME®
Colored panels consist of GALVALUME®-coated substrate that is prepped, and coated with silicon-polyester paint before fabrication
Bare GALVALUME® panels covered by 20-yearwarranty
Colored panels covered by 25-year limitedpaint warranty--Crimson Red warranty for 5 years

Wall panels for Commercial, Agricultural or Industrial 

  • Standard gauge: 26
  • Standard paneling: colored PBR
  • Optional colored PBA architectural panel (cost add)
  • Optional Bare GALVALUME® PBR (cost deduct, special quote only)
  • Optional colored or Bare GALVALUME® PBU (special quote only)


Roof Panels for Arsenal Steel Building

  • Roof system meets Underwriter's Laboratories Class 90 wind uplift rating
  • Standard gauge: 26
  • Standard paneling: Bare GALVALUME® PBR
  • Optional colored PBR panels (cost add)
  • Optional 70% PVDF paint (special quote only)
  • Optional standing Seam (special quote only)


Soffit

  • Standard gauge: 26
  • Standard paneling: colored PBR
  • Optional Bare GALVALUME® PBR (cost deduct)
  • Optional 70% PVDF** paint (special quote only)


Liner and Partition panels for Steel Buildings

  • Standard gauge: 29
  • Standard paneling: choice of colored PBR or PBU
  • Optional 26-gauge panels (special quote only)


Roof fasteners

The roofs of steel buildings are fully exposed to the elements, so special precautions must be taken to prevent rust. The most common cause of rust in metal roofs is the screw. Although the finish (Galvalume coating or paint) protects the exposed surface of the panels, the screws penetrate this painted surface and make direct metal-to-metal contact. If the screws do not seal properly or develop rust themselves, they will cause the panels to rust.


**PVDF coating (polyvinylidene fluoride) or Kynar® coating is a pure thermoplastic fluoropolymer that is non-reactive and possesses multiple coating benefits. Kynar coating is a chemical resistant, thick film barrier coating primarily used on chemical processing equipment due to it's low weight and low thermal conductivity. This coating is unaffected by most chemicals and solvents, and has excellent wear and abrasion resistance. PVDF coatings are especially resistant to solvents, acids and heat, and has low density compared to similar fluoropolymers. Kynar PVDF coatings also have a high dielectric strength, excellent resistance to weathering elements in harsh environments. Along with the ability to self extinguish, PVDF generates little smoke in the event of a fire.



Arsenal Steel Buildings Framing Specifications


Unless otherwise noted, the following specifications apply:


Built-Up Plate

  • All components made from high-quality first-run steel (what does this mean)
  • Red-oxide primer is baked on after welding
  • Tensile strength of web plate is 46,000 psi
  • Tensile strength of flange plate is 55,000 psi


Hot Rolled

  • All components made from high-quality first-run steel
  • Red-oxide primer is baked on after forming
  • Tensile strength is 50,000 psi


Cold Formed

All components made from high-quality first-run steel
Coils pre-coated with red-oxide primer before fabrication
Tensile strength is 57,000 psi
Coil thickness ranges between 16 and 12 gauge
Web depths are 8", 10", and 12"

ARSENAL STEEL BUILDINGS

FIRST AND FOREMOST:

AMERICAN STEEL

AMERICAN LABOR

NOW OUR EXPERIENCE IS IN YOUR ARSENAL 

Arsenal steel building's metal building specs 

303-339-0714

A local Colorado Steel Building Company 

ARSENAL STEEL BUILDINGS

Our experience is now in YOUR arsenal

safe rooms colorado